5G E2E slicing can be used to ensure the QoS and security of smart grid services. According to the

official 5GAA white paper, 5G E2E slicing technology can be used to provide secure, reliable and real-

time communication services for smart grid applications, to ensure the QoS and security of such

services. Reference: https://www.5gaa.org/wp-content/uploads/2019/03/5G-AA-White-Paper-onSmart-Grid.pdf

https://www.3gpp.org/ftp/tsg_ran/WG2_RL2/Specifications/202012_draft_specs_after_RAN_90/Dr

aft_36300-fc0.docx

3GPP TS 36.300

https://www.3gpp.org/ftp/tsg_ran/WG2_RL2/Specifications/202012_draft_specs_after_RAN_90/Dr

aft_36300-fc0.docx

https://www.etsi.org/deliver/etsi_tr/121900_121999/121915/15.00.00_60/tr_121915v150000p.pdf

TR 121 915 - V15.0.0 - Digital cellular telecommunications system ...

https://www.etsi.org/deliver/etsi_tr/121900_121999/121915/15.00.00_60/tr_121915v150000p.pdf

https://www.atis.org/wp-content/uploads/3gpp-documents/Rel16/ATIS.3GPP.38.473.V1620.pdf

ATIS 3GPP

https://www.atis.org/wp-content/uploads/3gpp-documents/Rel16/ATIS.3GPP.38.473.V1620.pdf

Thank you for your visit.

When a GPS divider is used, the maximum distance between the GPS antenna and the BBU is

shortened. This is because the divider splits the signal from the antenna into multiple signals that

can be distributed to multiple BBUs, thus reducing the distance between the antenna and the BBUs.

Sources: [1] Rymaruk, O., and Kovalenko, I. "GPS signal dividers for cellular base stations." IEEE

Antennas

and

Propagation

Magazine,

vol.

56,

no.

3,

pp.

121-126,

2014.

https://ieeexplore.ieee.org/document/6833669. [2] Albasri, N., and Al-Naffouri, T.Y. "GPS signal

distribution for a 4G/5G distributed antenna system." IEEE Access, vol. 7, pp. 100371-100382, 2019.

https://ieeexplore.ieee.org/document/8793094.

In Non-standalone (NSA) networking, the downlink peak rate of a CPE is affected by various factors,

such as the downlink transmit power of the NR base station, the CPE location, the quality of the radio

channel, and the configuration of the network. -The downlink transmit power of the NR base station

affects the signal strength received by the CPE and therefore can affect the peak rate achieved. -The

CPE location in relation to the base station can affect the signal strength and quality of the radio

channel. If the CPE is located farther away from the base station or in an area with high radio

interference, it may result in a lower peak rate. -Downlink BLER of 3% or above can result in

retransmission and thus lower peak rate. -Uplink transmit power of the CPE does not affect the

downlink peak rate of CPE as it is only related to uplink transmission.

According to the official 3GPP specification, the DCI of NR does not carry PUSCH power control

information. It carries scheduling information for the PUSCH and PDSCH and a PMI report.

Reference: https://www.3gpp.org/DynaReport/38-series.htm

The network layer in the transport protocol stack provides functions such as addressing and route

selection. It is responsible for finding the best route for data packets to travel from the source to the

destination. It also provides logical addressing and packet routing. The network layer does not

provide the transmission of binary data flows, MAC forwarding, or physical medium access.

https://www.oecd.org/education/skills-beyond-school/AHELOFSReportVolume1.pdf

ASSESSMENT OF HIGHER EDUCATION LEARNING OUTCOMES

https://www.oecd.org/education/skills-beyond-school/AHELOFSReportVolume1.pdf

https://about.usps.com/publications/pub32/pub32_terms.htm

Postal Terms

https://about.usps.com/publications/pub32/pub32_terms.htm

https://www.ohsaa.org/sports/bk/2014-15BasketballQ&A.pdf

Basketball Frequently Asked Questions

https://www.ohsaa.org/sports/bk/2014-15BasketballQ&A.pdf