View Mode
Q: 1
An international corporation migrates its primary and secondary data centers to Cisco ACI. The new architecture must include a disaster recovery solution for critical applications in the primary data center with these requirements: The secondary data center hosts dedicated workloads, which must remain isolated from the primary data center. Critical applications must have both Layer 3 and Layer 2 connectivity between data centers. The ACI policy must be consistent across the data centers. Flooding between the data centers must be restricted to specific VLANs. Which solution must be used to accomplish these goals?
Options
Q: 2
When planning to deploy a load-balancing service as a managed node, which ACI configuration must be included?
Options
Q: 3
What is an advantage of using OTV as compared to VPLS for data center redundancy?
Options
Q: 4
Refer to the exhibit. A Cisco engineer is configuring a PBR in a Cisco ACI data center scenario and plans to insert a transparent firewall. The APIC release is 4.1. the Cisco ACI fabric is configured to be the gateway for the servers and for the PBR node, and the Layer 4/ Layer 7 devices are deployed as Layer 1/ Layer 2 mode in the physical domain. Layer 1/Layer 2 PBR node interfaces arc also configured to be in a bridge domain and not in an L30ut. What is required for the consumer and provider connectors of the Layer 1/Layer 2 device for this scenario to work?
Options
Q: 5
A Cisco UCS instance has four interfaces on a UCS VIC. Where on the fabric interconnect does each interface terminate?
Options
Q: 6
An engineer deploys VMware ESXi hypervisor on blade servers. The virtual networking is managed by Cisco Nexus 1000V Series Switches. Which configuration aligns with Cisco recommended practices for providing high availability and a maximum throughput to the VMware ESXi hosts?
Options
Q: 7
Refer to the exhibit. A Cisco engineer is configuring a data center design scenario with Cisco MDS 90Q0 Series Switches. The cut-through routing mode is chosen for impf oved read operation performance. Each (SCSI host requires access lo storage through the IPS module. First, the engineer configures the TCP tuning parameters as enabled SACK, the maximum bandwidth of 1 Gbps. buffer size of 4096. keepalive timeout at 1s. and enables Path MTU. Then, the engineer must set the OoS of the ISCSI link. What is the maximum QoS value that must be set tor the ISCSI session?
Options
Q: 8
Which factor determines the choice of platform designing a Cisco HyperFlex infrastructure to support computer-aided design applications?
Options
Q: 9
DRAG DROP A customer is deploying a SAN based on Cisco MDS 9000 Series Switches. Each Inter-Switch Link must carry multiple VSANs at the same time. The access switch must share the same domain ID as the director switch to reduce the number of domain IDs needed in the fabric Drag and drop the operational port types from the right onto the boxes on the left to create a topology that meets these requirements. Not all port types are used. Port types are used more than once. 300-610 question
Your Answer
Q: 10
Refer to the exhibit. 300-610 question Fiber links are provisioned directly between the spine and leaf switches in the given LAN topology A/30 prefix has been configured over each fiber link to provide underlay connectivity for a VXLAN network. The network-engineering team must update the network configuration to provide the shortest possible convergence time if a fiber link is cut. Which action must the team take to meet the requirement?
Options
Question 1 of 20 · Page 1 / 2

Premium Access Includes

  • ✓ Quiz Simulator
  • ✓ Exam Mode
  • ✓ Progress Tracking
  • ✓ Question Saving
  • ✓ Flash Cards
  • ✓ Drag & Drops
  • ✓ 3 Months Access
  • ✓ PDF Downloads
Get Premium Access
Scroll to Top

FLASH OFFER

Days
Hours
Minutes
Seconds

avail 10% DISCOUNT on YOUR PURCHASE

  • USE THE CODE GIVEN BELOW ON YOUR CHECKOUT
DISCOUNT10